Proxmox VE system requirements (RAM, storage, hardware)

What does Proxmox VE need at a minimum?

The manual separates two levels. Its minimum requirements are “for evaluation purposes only” and should not be used in production. For production it recommends “high quality server hardware”.

Minimum (evaluation only)Recommended
CPU64-bit x86 with Intel VT or AMD-VIntel 64 or AMD64 with Intel VT or AMD-V
RAM1 GB plus memory for the guestsat least 2 GB for the OS and Proxmox services plus guests
Storageone hard drivefast, redundant storage, best with SSDs
Networkone network cardredundant (multi-)Gbit network cards

The manual has no separate tier for a home server; it only distinguishes between evaluation and production.

How much RAM do host and guests need?

The host itself needs at least 2 GB according to the manual, “plus designated memory for guests”. Your baseline is therefore those 2 GB plus whatever memory you assign to all guests together.

How much extra RAM do ZFS and Ceph need?

ZFS and Ceph need memory on top, “approximately 1GB of memory for every TB of used storage”. For ZFS the manual gives several calculations in different places:

  • Installation chapter: “4GB plus 1GB RAM for each TB RAW disk space”.
  • Storage chapter: ZFS needs “at least 8GB to start”.
  • For the ARC read cache the rule of thumb is “at least 2 GiB Base + 1 GiB/TiB-Storage”. A pool with 8 TiB of usable space therefore gets 10 GiB.

By default the installer limits the ARC to 10 % of host memory, at most 16 GiB. The formulas refer to different quantities (used, raw, available) and so give different numbers. If you want to plan cautiously, take the highest: for 8 TB of raw space that is 4 + 8 = 12 GB for ZFS alone.

For Ceph the manual recommends OSDs with at least 8 GiB of memory; by default an OSD needs 4 GiB. More on that in Building a Proxmox cluster with Ceph.

How much storage does the host need, and is 1 TB enough?

The manual names no minimum size for the system disk: the evaluation list only says “Hard drive”. More telling are the installer defaults for ext4 and xfs (with LVM):

  • Root volume: with more than 48 GiB available, a quarter of the disk, at most 96 GiB.
  • Swap: by default as large as the installed memory, at least 4 GB, at most 8 GB and never more than an eighth of the disk.
  • Free space in the volume group: with more than 128 GB available, 16 GB by default.
  • Data volume for guests: the rest.

On a 1 TB disk, system, swap and reserve therefore take at most around 120 GiB, and the rest belongs to the guests. Whether 1 TB is enough for them depends on the size of your guests; the manual gives no figure for that.

For the drives themselves it recommends SSDs with power-loss protection (PLP). It advises against consumer SSDs: “Using consumer SSDs is discouraged.”

Hardware RAID or ZFS?

For the operating system the manual names two ways: a hardware RAID with battery-protected write cache (BBU), or ZFS without a RAID controller. The same goes for local VM storage. The limit matters: “Neither ZFS nor Ceph are compatible with a hardware RAID controller.”

The installer chapter warns as well: “ZFS on top of any hardware RAID is not supported and can result in data loss.” According to the storage chapter, an HBA or an LSI controller flashed in “IT” mode is suitable. For ZFS it also recommends ECC RAM.

If you choose ZFS during installation, the minimum number of disks depends on the RAID type:

  • RAID1 (mirror): at least 2 disks of the same size
  • RAID10: at least 4 disks
  • RAIDZ-1: at least 3 disks
  • RAIDZ-2: at least 4 disks
  • RAIDZ-3: at least 5 disks

What network does Proxmox VE need?

One network card is enough to start; redundant Gbit cards are recommended, with more depending on storage technology and cluster. In a cluster the manual recommends a dedicated physical card for cluster traffic; for Corosync 1 Gbit is enough “in most situations”. Latency matters more than bandwidth: it should stay under 5 milliseconds between all nodes.

For high availability a cluster needs at least three nodes. For Ceph the documentation recommends at least 10 Gbps, used for Ceph traffic only.

What hardware does Proxmox VE run on?

The manual chapters on installation, storage, cluster and Ceph contain no hardware compatibility list. The platform is fixed: x86 with Intel 64 or AMD64 and a CPU with Intel VT or AMD-V. On ARM, Proxmox VE natively supports the NVIDIA Grace Hopper and NVIDIA Vera platforms; other ARMv9-A hardware is “best-effort”, and a Raspberry Pi is not supported.

For PCI(e) passthrough, CPU and motherboard must support an IOMMU (Intel VT-d or AMD-Vi), usually also switched on in the BIOS.

What helps with installation problems and with measuring?

On very old or very new hardware the Terminal UI installer helps; the manual says it has “generally better compatibility”. If the boot hangs on graphics drivers, the kernel parameter nomodeset helps. On x86 the installer menu also offers a memory test (memtest86+).

After installation, the bundled pveperf gives a rough measure of CPU and disk. The manual itself calls it “just a very quick and general benchmark”.

How do I try Proxmox VE before buying hardware?

Proxmox VE also runs inside a virtual machine (nested virtualization). According to the wiki this lets you test and learn before anything happens on real hardware. Plan plenty of CPU, RAM and disk space for the guest hypervisor.

So that the guest is not slowed down, the host must pass the virtualization extensions on to the VM. Proxmox VE does not do that by default. Also set the VM’s CPU type to “host”. On an Intel host, this shows whether nesting is active:

cat /sys/module/kvm_intel/parameters/nested

Y means active, N means not. Without the extensions it runs, according to the wiki, only with poor performance and is “not an option for productive environment”.

What applies to the test inside the guest?

The documentation names two restrictions: VMs with nesting active cannot be live-migrated. And if you try ZFS in the guest, use IDE or SCSI for its disks, not virtio.

On licensing and subscriptions, read Is Proxmox VE free?.

Nexilon is a certified Proxmox Silver Partner and plans, installs and maintains Proxmox environments.

Sources

Let's talk

Free initial consultation - no sales pitch, just an honest assessment.

Request a consultation →